applications products what's new contact about us

Microwave Hybrid Continuous Belt Dryer for fast and homogeneous drying of Technical Ceramics for example Hony Comb Ceramics

• Microwave Power: 36 kW
• Hot air: 72 kW / max. 80°C

 

Microwave Wood Glue Continuous Press

Plant dimensions: 8100 mm x 8125 mm

Microwave Power: 498 kW

 

Microwave Hybrid Continuous Belt dryer for fast and crackless drying of honey comb ceramics, technical or foamy ceramic

Microwave Power: 64 kW

Hot air: 35 kW / max. 80 ºC

Click image to enlarge

 

The continous microwave conveyor furnace MWD 28x1 kW has a usable opening area of W 800 x H 300 mm. The furnace is subdivided into 6 single modules. Depending on the used magnetron type each module has a microwave power of 28 or 56 kW. The whole length including the absorbing zones at the in- and outlet is approx. 10 m. The microwave generators are located above and below the conveyor belt. The special design of the microwave antennas guarantees a very homogeneous field distribution in the tunnel. Doors on the sidewalls of the furnace give full access to the conveyor belt. Microwave power and belt velocity are continiously controlable.

 

 

The universal microwave conveyor furnace MWDA 6x1,1 kW has a usable opening of W 600 x H 400 mm. The total length including the absorbing zones at the in and outlet is about 2,6 m. The used microwave antennas guarantee a very homogeneous field distribution in the heating zone. Microwave power and belt velocity are continiously controlable. Conveyor furnaces like the type MWDA find many applications in the manufacturing of chemical, pharmaceutical and laboratory products.

 

Universal Microwave Continuous Belt furnace

Microwave Power: 6 kW

 

Microwave Powder Dryer

• Microwave Power: 3 kW
• Possible application: Quartz-Flour-Drying from 0.2% initial humidity to 0.06% end humidity at throughput of 100 kg/h

 

Microwave Adsorbent Regeneration Systems M.A.R.S.
Economy and Performance in Materials Processing

• Length (L) = ~ 4,5 m
• Width (W) = ~ 0,9 m
• Height (H) = ~ 1,5 m

Benefits of using M.A.R.S.

• direct microwave heating and fast on/off ability results in energy savings
• control of material transport within the kiln coupled with accurate and rapid temperature control allows for optimum heating uniformity and high efficiency
• compact, automated and easy-to-operate systems requiring low labor
• low gas consumption for controlled atmosphere applications
• emission control/vapour recovery systems easily adapted to M.A.R.S.
• competitive capital and installation costs

Typical applications

• carbon reactivation
• mineral ore treatments
• ceramic powder and glass frit processing
• food product drying, heating and roasting
• material cleaning and recovery

 

The microwave flow heater MDE 6x1 kW is designed for heating chemical and pharmaceutical liquids. The flow through plastic tube withstands aggressive media and makes possible fast and precise temperature control. E.g. this is important during galvanic processes. Tube diameters up to 40 mm can be realized. The flow heater has a total power of 6 or 12 kW. If more power is needed, the flow heaters can be cascaded.

 

The microwave flow heater MDE 1,2 kW is used for the preheating of glass fibres in pultrusion. With different applicators profile diameters up to 50 mm can be treated. A three stub tuner guarantees good matching to different loads. The microwave power can be adjusted without any inertia, so temperature control even at high speeds is no problem.

 

The applicator PUL 3xCF is used for the preheating of three carbon fibre bundles at the same time. Carbon fibre pultrusion was very difficult until yet, because the conductive fibres cause a large leakage radiation. With a special design of the in- and outlets of the applicator it was possible to decrease the radiation to a legal limit.